SACC-SQ-M12MS-4CON-20/0,5 - Device connector front mounting
1419784
Device connector front mounting, Universal, 4-position, Pin, straight, M12, coding: A, on free cable end, Front mounting, Square flange, Individual wires, cable length: 0.5 m, 0.34 mm2, TPE litz wire
Notes on operation The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration.
General Contact connection method: Crimp connection
Safety note
Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.
• WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and electrical device engineering.
• When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must be grounded
• Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by Phoenix Contact
• Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
• Ensure that the protective or functional ground has been properly connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector
• The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12).
Mounting type Front mounting Square flange 20 mm side length
Assembly note 20 mm side length
Product type Circular connectors (device side)
Application Signal
Sensor type Universal
Number of positions 4
No. of cable outlets 1
Shielded no
Coding A
Thread type M12
Insulation characteristics
Overvoltage category II
Degree of pollution 3
Material Zinc die-cast, nickel-plated
Flammability rating according to UL 94 V0
Seal material FKM
Material of grip body Zinc die-cast, nickel-plated
Contact material CuZn
Contact surface material Ni/Au
Contact carrier material PA 6.6
Material for screw connection Zinc die-cast, nickel-plated
Conductor material Tin-plated Cu litz wires
Rated surge voltage 2.5 kV
Contact resistance ≤ 3 mΩ
Insulation resistance ≥ 100 MΩ
Nominal voltage UN 250 V (AC)
250 V (DC)
Nominal current IN 4 A
Max. conductor resistance 57.6 mΩ/m
Conductor connection
Connection method Individual wires
Contact connection type Pin
Conductor cross section 0.34 mm²
Tightening torque 3 Nm ... 4 Nm (Installation-side)
Mechanical data
Insertion/withdrawal cycles > 100
Connection 1
Head design Pin
Head cable outlet straight
Head thread type M12
Coding A
Connection 2
Head design free cable end
Cable length 0.5 m
Cable type TPE litz wire
Signal type/category Universal
Wire diameter incl. insulation 1.2 mm ±0.07 mm
Single wire, color brown, white, blue, black
Cable cross section 0.34 mm²
Conductor material Tin-plated Cu litz wires
Conductor structure signal line 7x 0.25 mm
AWG signal line 22
Material wire insulation TPE
Thickness, insulation 0.21 mm (Core insulation)
